Awesome Hank

A Stpe By Stpe Guide To Repairing A Running Toilet

Fixing a running toilet is one of the basic toilet repair jobs. Often the problem can be diagnosed and even repaired by an amateur plumber. There are a number of good how to articles on the Internet. In this summary article, I have put together the best suggestions from other articles in order to come up with the perfect flow sheet for diagnosing the cause of a running toilet.

1) The first step is to open up the top of the tank and peer inside:

2) If the tank is full and the flapper is closed and water is running over the top of the overflow tube. Then the flapper is working properly, but the fill valve is working improperly.
a. Turn off the water at the toilet shut off valve
b. Check for a misalignment of the float arm. A misalignment of the float arm allows the water to rise too high and therefore to trickle over into the overflow pipe and continually run into the toilet.
i. Pull up on the float with your hand. If this action stops the flow then adjust the level of the float.
1. If the float is around the valve post, pinch the metal clip and slide the float down the wire.
2. If the float screws in, try unscrewing it a bit and moving it further down the float arm.
3. If there is a ball on an arm, try turning the small screws on top of the valve. Sometimes, you can also bend the arm further down.
4. Make sure the float ball isn’t touching anything else
5. Make sure the float ball isn’t leaking or filling with water.
6. No matter how you adjust the float ball, adjust it so the tank stops filling when the water is about an inch, (2.5cm), below the to;p of the overflow tube.

3) If you notice that the rubber flapper won’t close, try to close it manually. If this maneuver fixes the leak, then consider the following.
a. Is the chain catching on something? dislodged or tangled
b. Is the flapper catching on the chain?
c. Is the float connected too low on a flapper chain (flapper chain float not the ball float) Try raising the float to see if this solves the problem.
d. If none of the above maneuvers solved the problem consider the following:
i. Is the flapper aligned with the opening?
ii. Is the flapper discolored on the bottom, (continuous leak)
iii. Is the flapper simply just old and stiff (and needs replacing)?
iv. If you answered yes to any of these questions, then the problem is an old torn or worn out flapper assembly
v. Replace the flapper

4) If you have a ball seal instead of a flapper, is the wire that lifts the ball straight and does it move freely?

5) Sometimes the leak is the results of sediment and water deposit build-up in the flush valve seat, this can prevent the rubber flapper from dropping into the seat properly, and leads to a leak.
a. Try thoroughly scrubbing and cleaning the valve seat and see if that stops the leak.

6) If the toilet runs intermittently, then, in all likelihood you have a slow leak.
a. Place a dye tablet or a few drops of food coloring in the tank if after an hour or two without flushing, you see this dye in the bowl, you have a slow leak
i. The most common cause of slow leaks is a leaky flapper
1. Cleaning may work usually best just to replace the whole flapper
b. Replacing the flapper:
i. To perform the replacement, simply close the valve sticking out of the wall under your toilet tank,
ii. Flush the toilet
iii. Pop the old flapper off its hinges, disconnect it from the chain, and pop the new one into place
iv. Run a finger carefully around the rim where the flapper seats
v. Remove any uneven buildup of minerals that might cause a leak
vi. Use a sponge with bleach to clean the flapper seat.
vii. Open the valve all the way
viii. Try flushing a few times
ix. Trim and adjust the chain by trial and error

7) Occasionally, the valve on the fill tube is low, and close to the water level, the valve may act like siphon and pull water back into the fill tube.
a. Adjust the valve height or tube height up, or adjust the water level down.

If water is leaking through the fill valve, you need to consider replacing one or more of its parts or else the whole fill valve
a. If the rubber seals are worn, replace the rubber seals
b. One or more of the non-rubber components may break in the toilet’s water valve mechanism: -
i. Try fixing the broken part with epoxy
c. Replace the whole valve.

Tags: bathroom repair, how to fix running toilet, repair, running toilet, toilet
Posted in Bathroom · July 23rd, 2010 · Comments (0)

Fixing Computer By Yourself

It is not that hard to repair your own computer in some cases, especially when it concerns software. Fixing hardware problems on your computer might be a little more exciting, but also harder, so it is better to contact a good computer repair in Kings Cross and have professionals open your laptop up and replace a particular part. It is always better to entrust all computer parts replacements, like laptop screen replacement in London, to professionals. But, sometimes, you can fix your own computer pretty easily, when it has some software issues.

The first thing you will do for your computer repair is perform some detective work. Always write down an error you get on your computer screen. You should also write down any details that might help you determine the cause of the error. Try to remember what you were doing when the error appeared, if there was any new software or hardware or if there was a power failure and other circumstances. The bad thing is that not all errors can be accurate. There are many meanings to some errors and it often depends on a situation. For example, the so-called blue screen of death appearing in Microsoft Windows can be caused by many things. Anyway, you should always pay attention to the message appearing and write it down. The message can help you define whether it is a hardware or software issue.

Then, you should do the search on the error you got. You can get some good search results, even if you don’t have the error in front of you but you can still describe it. Try to type in the exact error you received in the search engine. You will get some useful specific information on the error and it will help you find the right problem solution.

You can also find a lot of articles about the most common computer repairs and the ways to perform them. You will be able to find step-by-step instructions, which will make resolving the issue even easier. So, when you find the solution to your problem, it might seem like a little too hard for you to do. But, this information can still be useful to you, because you will use it to describe the problem to the professionals in computer repair company. The faster and better you will be able to describe the issue, the faster your computer will be fixed. This will also help you reduce the cost of the repair in some cases.

The most valuable recommendation that could be given to all users is to keep all important data backed up. This will make computer repair a lot less stressful and troublesome. Having all data backed up will help you in case you need to reinstall the operating system without a chance to do a backup.

This article was written for High Impact SEO – the best place to find SEO Services.

Tags: computer, Computer repair, laptop, laptop repair, repair
Posted in Computers · July 22nd, 2010 · Comments (0)